Binary logs are essentially a recovery mechanism for Real-Time index data and also of attributes updates of plain indexes that would otherwise only be stored in RAM until flush. With binary logs enabled, searchd writes every given transaction to the binlog file, and uses that for recovery after an unclean shutdown. On clean shutdown, RAM chunks are saved to disk, and then all the binlog files are unlinked.

Binary logging is enabled by default. The default location for binlog.* files in Linux is /var/lib/manticore/data/. In RT mode the binary logs are saved in the data_dir folder, unless specifed differently.

Binary logging can be disabled by setting binlog_path to empty:

searchd {
...
    binlog_path = # disable logging
...

Disabling binary logging improves performance for Real-Time indexes, but puts their data at risk.

The directive can be used to set a custom path:

searchd {
...
    binlog_path = /var/data
...

When logging is enabled, every transaction committed into RT index gets written into a log file. Logs are then automatically replayed on startup after an unclean shutdown, recovering the logged changes.

During normal operation, a new binlog file will be opened every time when binlog_max_log_size limit is reached. Older, already closed binlog files are kept until all of the transactions stored in them (from all indexes) are flushed as a disk chunk. Setting the limit to 0 pretty much prevents binlog from being unlinked at all while searchd is running; however, it will still be unlinked on clean shutdown. By default, there is no limit of the log file size.

binlog_max_log_size = 16M

There are 3 different binlog flushing strategies, controlled by directive binlog_flush:

• 0, flush and sync every second. Best performance, but up to 1 second worth of committed transactions can be lost both on server crash, or OS/hardware crash.
• 1, flush and sync every transaction. Worst performance, but every committed transaction data is guaranteed to be saved.
• 2, flush every transaction, sync every second. Good performance, and every committed transaction is guaranteed to be saved in case of server crash. However, in case of OS/hardware crash up to 1 second worth of committed transactions can be lost.

Default mode is flush every transaction, sync every second (mode 2).

searchd {
...
    binlog_flush = 1 # ultimate safety, low speed
...
}

On recovery after an unclean shutdown, binlogs are replayed and all logged transactions since the last good on-disk state are restored. Transactions are checksummed so in case of binlog file corruption garbage data will not be replayed; such a broken transaction will be detected and will stop replay. Transactions also start with a magic marker and timestamped, so in case of binlog damage in the middle of the file, it is technically possible to skip broken transactions and keep replaying from the next good one, and/or it is possible to replay transactions until a given timestamp (point-in-time recovery), but none of that is implemented yet.

Intensive updating of a small RT index that fully fits into a RAM chunk will lead to an ever-growing binlog that can never be unlinked until clean shutdown. Binlogs are essentially append-only deltas against the last known good saved state on disk, and unless RAM chunk gets saved, they can not be unlinked. An ever-growing binlog is not very good for disk use and crash recovery time. To avoid this, you can configure searchd to perform a periodic RAM chunk flush to fix that problem using rt_flush_perioddirective. With periodic flushes enabled, searchd will keep a separate thread, checking whether RT indexes RAM chunks need to be written back to disk. Once that happens, the respective binlogs can be (and are) safely unlinked.

searchd {
...
    rt_flush_period = 3600 # 1 hour
...
}

By default the RT flush period is set to 10 hours.

Note that rt_flush_period only controls the frequency at which the checks happen. There are no guarantees that the particular RAM chunk will get saved. For instance, it does not make sense to regularly re-save a huge RAM chunk that only gets a few rows worth of updates. The search server determine whether to actually perform the flush with a few heuristics.

When you use the official Manticore docker image, the server log is sent to /dev/stdout which can be viewed from host with:

docker logs manticore

The query log can be diverted to Docker log by passing variable QUERY_LOG_TO_STDOUT=true.

The log folder is the same as in case of Linux package set to /var/log/manticore. If desired, it can be mounted to a local path to view or process the logs.

Manticore Search accepts signal USR1 for reopening server and query log files.

The official DEB and RPM packages install a Logrotate conf file for all files in default log folder.

A simple logrotate conf for log files looks like:

/var/log/manticore/*.log {
       weekly
       rotate 10
       copytruncate
       delaycompress
       compress
       notifempty
       missingok
}

mysql> FLUSH LOGS;
Query OK, 0 rows affected (0.01 sec)

In addition, the FLUSH LOGS SQL command is available, which works same as system USR1 signal. Initiate reopen of searchd log and query log files, letting you implement log file rotation. Command is non-blocking (i.e., returns immediately).